For $29/mo, we provide access to advanced level technicians who will answer your questions on any Macbook board related matter to the best of their knowledge promptly & walk you through how to solve your problem so you can deliver a working board to your customer.
Hi,
have a MacBook Air 820-3437 with liquid spill and burn marks at R5100 intermittent power. The number 1 pad is burnt I removed the resistor noticed it connects to many many things.
Problem is can't get solder to stick to that pad. I used flux and solder then scraped a little but is not...
2014 MacBook Pro 13 inch need to find out where the jumpers are at on the logic board to see if it will start .
doesn’t start from the keyboard .
A1502 emc 2875
Thanks
Hi,
I have a 820-3476 Liquid Spill not real obvious damage. hit power button 3 beeps not passing post. Can this be U5870? (there was a little greasiness there)
Thanks,
Rick
Hi,
2010 2.66 i7 820-2850
MacBook Pro that I replaced the Tandan Cap now Video works fine.
When I plug power into MagSafe Machine starts up.
Keyboard works letters work and trackpad works.
If I push the power button on keyboard machine instantly shutdown. I try to start by pushing power button...
Replaced top case MacBook Pro 4924 liquid spill on trackpad. Also replaced Right IO board cause when connected with cable 821-1790-A machine will not boot.
Tried 2 cables.
I believe there is a short on logic board related to J9510. Any Clues?
Thanks
Hi
I have a early 2011 MacBook Pro 2011 goes through book process and all works until it gets to last screen which is BLANK White.
I tried a different drive but same result.
Im going to replace the tangent capacitor but has a different number then previous on.
I am going to replace with a...
Hi,
I have a 820-2915 doesn't pass post getting 3 beeps.
Changed memory tried both slots no good.
I plugged in usb mouse and it gets a light after I start machine.
Any ideas?
Tx
Hi
Im working on a 820-3437 board I have a second board to compare with.
Schematic says there should be a chip in certain location but second board matches first board with no chip there?
Am I correct in believing the second board?
In the U5000 Group
Example R5445,5475
If it runs hot when I put...
Hi
I looking at 2 logic boards and there is no component on both boards for the same location.
Are the Schematics always correct? I also search for a substitute part. Says should be a capacitor but its black and not grey.
I see many places on board that look like components could go there on...
Hi Im working on a 820-3437. R5475 4.53k
This is a non current sensing resistor?
Need to replace some resistors. Probably blew away don't know.
I assume I should order from mouser?
Does anyone have their part number?
Thanks
I have a 820-3547 EMC 2674 15" MacBook Pro 2012 not booting MOST of time.Sometimes machine will gong and boot but rarely. When it does gong reset smc and pram 4 times.
Fans spin no gong no video.
I suspect failing GPU. Is there anything I should check before calling this one not repairable?
I...
Hi doing first real logic board component repair.
Replaced capacitor using schematic and your video.
now MacBook Pro 15 2010 in constant reboot.
am I using the wrong part? I believe th cap is proper orientation.
Thanks!
Newbie Rick
Hi
Im all setup equipment wise. Where can I find basic Louis? Videos covering heat station temp removing components and soldering and heat station, how to test components?
I guess how much time should it take to remove a chip without harming the logic board?
Thanks
Rick
Hi
I have a MacBook Air 1466 EMC 2632 customer spilled beer on it and fried the Trackpad/Keyboard cable connector. Part has much plastic so I assume I can't remove it without melting the plastic.
Where can I order the logic board trackpad connector from?
Thanks