For $29/mo, we provide access to advanced level technicians who will answer your questions on any Macbook board related matter to the best of their knowledge promptly & walk you through how to solve your problem so you can deliver a working board to your customer.
PU1900
1-2 - 2.37Ohm
14-15 - 4.65Ohm
It cycles on each of these every sec, so I added both measures before and during the cycle
Charger Only - B+ 13.56V/0A - 13.6V/1.4A
Battery Only - B+ 9.5V - 8.3V
Charger & Battery - B+ 13.34V/1.5A - 11.5/4.8A
Hi Guys, I am sorry if non-apple posts are not allowed.
I am dealing with this LA-G341P, which had heavy liquid damage around the Audio board, Battery charging circuit. I went and cleaned liquid areas and left the audio board disconnected.
It had blown PQ1900/02/3 as well as a trace on...
It seems like the Camera is playing up. Disconnected and monitoring the situation.
Probably nothing can be done without taking up the glass and replacing the camera, right?
Thank you again
The only severe liquid impact is on the PMIC. Is there anything else I can check? The system diagnostic says all is good.
I was thinking perhaps a corroded pad on PMIC is losing contact when more power is drawn. Now it does it even when casually browsing the web.
The whole system runs fine until I start a video on 4k. It plays for a second and freezes with colourful patches and reboots.
PMIC voltages on surrounding coils vary from 0.6 - 0.8V. Three big coils on the opposite are all on 3.3V
No short on any components surrounding UP800
Got this with spatters of water all over the place, but the main corrosion is around PMIC. Cleaned and reflowed, but suspecting bad contacts underneath. Before I lift it up (haven't done it on such big chips) and reball it. Any recommendations or suggestions?
Done this method on CD3215 and is a...
Tested battery, which works on other mac - Still loud fans
Got gswitch software to switch between GPUs and left for a while - still fans loud
Looking at the sensor heat pipe incoming/outgoing air ones are off. Any idea where these sensors could be on the board (Q5502 / U5570 seems to be a...
This Macbook has a previous repair around U9200/10, U8310/50 and U8900 ICs, and a battery replacement.
AHT is not initiating stating a missing .efi, TectoolPro 11 haven't detected any anomalies.
Replaced the trackpad and trackpad cable. It worked fine for a week and suddenly start running the...
When I reboot usually comes online and works as expected. I can load from it, and it runs perfectly with no SSD errors. Haven't seen it come with a question mark again after I shut down and rebooted from the previous question mark. It loads up straight away until the next time when it crashes...
It turns on and works fine for a while, but often when it starts or awakes from a long-term not usage turns on with a question mark. Same when used for an extended period of time.
Previous liquid damage around U3890/5 doesn't seem to be related to SSD lines. Also, some around R3773 and U3700...
I don't have this exact board for donors, but the two 00840 I have show as 1M.
Perhaps the only option now is to source the B03 version. 00840 and 01041 donors I have are using the C version.
It is a long shot but I do have two TPS65982DA
No more short on UPC_XA_UART_TX after I replaced it with the expected 1M.
I was just reading about some CD3215C compatibility issues with CD3215B and how TBT ROM could be reprogrammed. I do not have B ones in stock. Could this be something causing it?
Seems like R3205 was shorting to 0 Ohms. Replaced and still not getting PP1V1_UPC_XA/B_LDO_BMC stuck at 5.2V 0.02A
Diode mode measurements are quite close to these of an A1708 820-00840 I use as a donor.
Seems like this had a bad charger as U3200 had a burn mark on the dye.
Replaced U3200 with a "new" one I had, still not powering on, then noticed having short on C3108 - PP3V3_UPC_XA_LDO
I replaced U3100 twice with reballed ones I pulled from another board. Now is stuck on 5V 0.02A with no...
Sorry I wasn't clear. No audio on speakers. Audio plays over HDMI/BT. The video keeps playing with no sound when disconnected HDMI/BT. While before I connected HDMI, it would stay stuck on a frame but show playing.
Yes Audio Amps were nasty, probably still corrosion underneath, haven't UC'd yet. This is how it was when remove dthe middle one
HDMI Audio is working
BT Audio is working
Video start playing now once I get it connected, it keeps playing when disconnected too.
OK managed to bring it to life, it turns on now, and I can load the system. Though due to the missing amp seems like the sound is not working okay and not getting recognised. Comes up with an error message - "Could not load up sound preferences".
Does anyone have an idea where I can get it...
I have replaced the U7400. No fan spin stays at 0.28A and can see the replaced Q7510 gets hot.
But have very low resistance on CPUIMVP_PHASE1/2 - 1Ohm. Is it expected?
Also seems like it blow the Q7510 again, shall i replace it one more time? I have lifted the coils around the CPU and lower...