Search results

The logic behind this appears sound, but really only works for phones that have no other existing issues after intial water damage. Basically, a really expensive vacuum dehydrator. However, what they dont mention is that it does nothing for any remnants left behind after the water content...

Ill second, third, whatever it.... Got one and sits on the shelf. Fn waste of time and money for repairs. However, if youre buying parts and want to test rated capacitance against actual; maybe only then its beneficial.

Ok, so more research on filters has revealed new data. Athough hepa is what we think of as the standard in filtrattion it may not be suited to what we need. However can still be an optional add for those that like overboard protection and want to clean air while removing the gas or simply...

This one i have heard too. But i really question this as the hoses are far enough down the stage that temps should have cooled to an acceptavle level. Of your referring to the loc-tite. Its not actually a hose its a solid material with a much higher heat dissappation than a rubber hose...

What pbx do use? Typically, multiple ring-to setup is controlled by creating ring groups. It does not require additional trunks asTrunks are connections to/from service provider.

This is probably the best option so far. Hopefully this Chinese manufacturer sends me some info soon. I'm thinking their raw supplies could build the same filter for about $25. But this is just speculation.

The one youre looking at is going to very large, but has good power for sure. Just make sure youre comfortable with the external dimension as that will be your bare minimum internal dimensions for your enclosure. These units are also very loud, so youll have make sure u insulate well without...

Im assuming the purpose of this is to get a smaller and longer probe tip?

Heres a fan for building a monster...(lots of lift) http://m.ebay.com/itm/3-Stage-Vacuum-Motor-5-7-DIA-105-CFM-1200-Watts-10-Amp-120-Volts-/111662004093?nav=SEARCH Heres something powerful, but not insanely so...

Also, have you guys looked at fans yet. I dont recommend basic computer fans. Look at server fans as bare minimum. Much more torque and higher rpms, but they are louder. You can always insulate enclosure to muffle sound.

To minimize blow back you would want to use a combo of louver and right-angle down draft to block outside air from pushing back. For extra protection still use carbon filter stuffing in hose duct. Its a half measure approach, but something is always better than nothing

The only problem i have with venting to outside is efficiency. If you are moving even only 150cfm...then you are dumping 1500 cubic feet of conditioned air every 10 minutes. That makes for a heafty ac bill and puts added strain on your ac system. If you can do this in an isolated room with...

Also, due to the air gap design of my layout, i do not believe it matters which side the filter is on in regards to dispersion of airflow. My preference is to place before the electronics to keep them as clean as possible without having to seperately enclose However, i do think adding an air...

In the fa 430 the filter is before the fan. The fan is located under a seperate sealed enclosure. Maybe louis would be kind enough to share some pics. I tried to find some replacement fan parts for the unit, but appears hakko doesnt sell that. Also, i found a supplier of hepa filters and...

Should have looked at link before i posted... Site says dummy board. I doubt theres even any circutry under the covers. Ots about the same as a dummy phone... For show only and a waste time of time for parts

I wouldnt purchase something that says fake board if you want to repair for use. There are lots of pseudo iphones (clones) and the chips are not legit. Maybe some of the filters, resistor, etc may cross over... But id bet they are sub-par. Purchase at your own risk.

here is a link to a hakko filter for sale. I think these can be done for cheaper, however, box can be easily modified to accept. https://www.riogrande.com/Product/HE...FVA8gQodAaYBoQ Link to info on filter design (good info for building concepts)...

Another awesome find. I actually use the same vortex fan (made really for grown houses) as the blowers for my positive pressure room. They are loud as shit. Ill have to lool into it

Good post. I was unaware of the 3 filter components. Knew they used multistage, but again im lazy, so i never went past just straight carbon filter. Ill do some surfing to locate, but if anyone knows or finds a good source for all filter component... Please share. Might be possible to...

Pictures of commercial units may help you understand/self-assure that these units are not as complicated as their price tags suggest, but its not necessary to build a professional unit. Understanding the basics behind creating a sealed vacuum enclosure and quality mechanics is all that is...