Search results

Ok, I have my answer

yes, and I've recheck again and again. They are really OL

I've tried again to force DFU, no way. When using FORCE_DFU, I should only plug USB-C to USBC Mac with AC2, no casing, no special key to press, just the motherboard with USB-C (left port) cable to Mac runnning AC2 J3300 diode mode. 2 tpusbcpp20vxb OL 3 usbcxbcc1conn .693 6 usbcxbcc2conn .702...

CanI use CD3217 ? I don't have any CD3215

it's working, I remove UF300.Thanks for your help

My bad, JE700 has a few short...18,20 JE701 29,30,31,32 PPVBUS_USBC1 .151 25 OL 20 USBC1_CC2_CONN .638 18 USBC1_SBU1 .670 17 usbc1_usb_top_n.845 15 usbc1_usb_top_p.846 14 Usbc1_usb_bot_p .841 12 usbc1_usb_bot_n .838 8 usbc1_cc1_conn .668 6 usbc1_sbu2 .699 2 tp_usbc1_pp20v OL JE700...

ok, I will replace it, hope it will work

Hi, Macbook, side on 1 cm water on bag. Only USB-C side- Magsafe was on water. IT-Shop clean the board, board looks ok. JE700 - port USB-C - nothing, USB-C multimeter stay black JE700 - port USB-C - nothing, USB-C multimeter - 20V - 0.1 amp I have ppvbususbc diode mode .147, does that point...

Yes, I've tried manual DFU "A1932 & A2179 between pin 1/R8010 to pin 1/C7845, or other convenient 1V8_SLPS2R point" doesn't work. PP1V1_SLPS2R Diode mode .255 - Voltage 1.1V PP0V9_SLPDDR Voltage 0.9 PVDDCPUAWAKE_SW0 Voltage 0.76 PVDDCPUAWAKE_SW1 Voltage 0.76...

DZ3351 - diode mode .539 - USBC_XB_CC2_CONN Need to replace U3200 ? removing is not enough ?

DB529 is blown. USBC_TA_USB_TOP_ N was shorted. I remove it, now diode mode is .556 (What component are DB ?) Still not booting. UB300 - USBC_TA_CC2 diode mode = .550 UB300 - USBC_TA_CC2 diode mode = .550 UB400 - USBC_TB_CC1 diode mode = .548 UB400 - USBC_TB_CC2 diode mode = .552...

P1V8G3S_EN on R084 switch from 0 to 1.8V every 3 secondes P3V3G3S_EN on R8061 switch from 0 to 1.8V every 3 secondes PP1V8_SSD on C8732 switch from 0 to 1.8V every 15 secondes, stay on 1,8 for 2 seconds I've mentionned those above, it's not what you asking? PP1V8_SLPS2R 1.8 V...

U3000 looks ok, no short on USB_SOC_P/N but Mac doesn't start. It goes up to 0.5 amp and drop to 0.1 there's 4 USB-C. Top left port USB-C - nothing, USB-C multimeter stay black Mid left port USB-C - 20V - up to 0.5 amp and drop to 0.1 Top right port USB-C - 20V - up to 0.5 amp and drop to...

Sorry for my ignorance but boardview show a chip but there's nothig on the motherboard

I did, I get 20V,, 0.7 Amp but it doesn' start

So I can try to remove UE010 ?

Hello For data recovery only, does 820-01041-A need U3000 to start ? U3000 blown, I removed it, pads 6 & 7 gone. I see a short on PIN2 USB_SOC_TYPEC_N. It goes to UE010 on schematic but the board is a little bit different. If I remove UE010 would Mac start ? Thanks

Hello, A1932. it was hanging from time to time and one day didn't boot anymore. I've tried several time to put it in DFU but no way. USB-C chargeur connected, motherboard only, out from case Thanks Sam

thanks

Hello I got this A2337 to replace the screen. After screen replacement I see battery is not charging. Customer store it for two years before bringing it replace the screen (It should have been taken under warratny, those A2337 screen failure are very common). Is there a way to "wake up" the...