Search results

Thank You 2informaticos for All Your Help. I REALLY APPRECIATE IT!!!...Here are the U7100 Readings on the pins you Requested... PPBUS_G3H 4.40mOhm in Diode Mode With Red On Ground... U7100 Readings... Pin 1. 0.007v Pin 2. 16.07v Pin 3. 3.924v Pin 9. 0.033v Pin 12. 3.412v Pin 13...

Reading On Pin 2 of F7141 PPBUS_G3H 4.40mOhm in Diode Mode With Red On Ground

ANYONE have any Suggestions?

Okay Replaces U7100 and Got my Green/Orange light back and SYS ONEWIRE AND BC AKOK is Back But getting 1.09V on PPBUS_G3H, Still have 3.4V in PP3V42_G3H...trying to get the Values for R7110/R7111 and C7111 But I don?t have the schematics for the 820-00426 Just have the Schematics and Boardview...

Getting 0.925 mOhms on Both sides of R7029 and It is reading properly as a 2.0K Resistor

U7000 Pin 1 = 0.000V Pin 4 = -0.000V Pin 5 = 0.024V Also getting 3.4V on pin 5 of 7001...But 0.000V on Pins 1, 2, and 4

Here are the Readings from U7100 Pin 1 = 15.86V Pin 2 = 16.30V Pin 3 = 0.00V Pin 9 = 0.029V Pin 12 = 3.41V Pin 13 = 3.38V Pin 14 = 0.00V Pin 15 = 0.048V Pin 18 = 0.117V Pin 19 = 5.50V Pin 20 = 5.50V Pin 27 = 0.001V After checking Voltages on U7100 I have now lost green Light and Lost Previous...

I?ll check the 12 Lines you mentioned on U7100 ?

No Liquid damage Not Dropped,...Customer says Battery went dead and that was it...That?s all I know...The Board is SUOER CLEAN all over.

Here are Some Measurements PPBUS_G3H 0.975V with Board plugged in PPBUS_G3H Diode Mode -0.927V PPP3V42_G3H 3.4V PP5V_S5. 0.942V R7029 (Pin 1) 3.39v (Pin 2) 3.4v C7505 Pin 1. 0.942V iSL 6259 4.8 Ohms Between pins 17&18 23.2 Ohms Between Pins 27&28 Any Help is GREATLY APPRECIATED

Yes...Sorry...I Meant its reading 19.89V and just keeps going from 10mA - 61mA on USB-C Meter

3.7V Max...Okay...Aprox How many Amps Max?

3V3_SUS is 0.5 ohm

I Have a Couple more U8200s But I believe your right and there is a shirt on the 3v3_SUS line....any ideas where in the board I should start to find out what?s causing the short?....I REALLY APPRECIATE all your help :)

Measured C1744 Pin 1 (pp3v3_SUS) Reading is 0.5ohms

I replaced U8200 off of a Donor board and when the board was plugged in it Blew out U8200 so I Immediately unplugged the charger and removed the U8200... I am still getting the same measurements as before I put the U8200 on...Here are the Measurments on the pads of U8200 with it off... Pin 1...

Thank You for Your response 2informaticos.... I Just Noticed U8200 for 3.3v SUS Switch is Completely Missing on the Board!! Can I replace U8200 from another 820-00281 Board or a 820-00928 Board? I have Both donor boards here.

PP3v3_S5 = 3.31v PP3v3_SUS = -0.000V

Hello, I have a 820-00281 that has No Liquid Damage at all and Will Not turn on...Board reads 19.94V - 10mA to 61mA... Here are some Measurements I have taken with the Board out of the Machine. PPDCIN_G3H = 20V PPBUS_G3H = 12.56v PP3V3_G3H = 3.39v PP5V-S5 = 5V PP5V_S4 = -0.00V PP5V_S0 = 0.012V...

Anyone have any Suggestions? :(