Search results

0.04 microfarad capacitor but the resistance cannot be calculate d

but is it possible to detect this fault?

I have found corrosion in C8111 R8111 and in C3280 and C3281 without short but I have still repaired the tracks because they did not have continuity I do not have voltage in L7310/20 L7430 L3095 L7701 L7630=1v L7560=3.28v L7520=5.10v L7130=8.5v thanks

pins 17/18=04.0 (scale 200) pins 27/28=40.4 (scale 200) I have been able to observe some corrosion on the U3210 that my colleague overlooked. I have cleaned the area and installed the new R3211 because cleaning made it disappear but the problem has not improved.

I have double checked and all coils seem to be fine

Well, I can confirm that we have tested used original batteries and new compatible ones with the same result. The problem only appears if we connect the trackpad and keyboard. We have tested 2 topcases from other computers in good condition and it continues to happen. I can confirm that the...

If the percentage increases and it seems real, but now we have tested it with an old battery, 1014 cycles, recommended repair, it has charged up to 18% and has not turned off for a few minutes and is at 13%, a very curious case... the first test was with a new, unused battery and it did not...

That was in normal mode without turning on with magsafe on orange led but without fan spin

3V3_G3H_RTC=427 no short

It doesn't work, no liquid damage or burned components. led green change orange without battery, I try with other I/o board and flex. In bypass mode we managed to turn on but without image internal o external monitor (it's only possible with keyboard if we try to bypass with smc pads we can't)...

yes, L7310=1.22v The device works perfectly with MagSafe, it never turns off or restarts. But with a battery it barely stays on for a few seconds/minutes.

hi again C7050=12.20v

hi again, 0.02v

Hello, I received this device that does not turn on, very dirty fans, perhaps overheating... I have checked the motherboard, it does not seem to be damaged. no dfu mode some voltages: PPBUS_G3H=4.18v 3V3_G3H_RTC=0v L9020=0v L9030=0v L9080=0v mode diode to ground PPBUS_G3H=386 L9020=433...

genuine magsafe 61w some voltages: PPBUS_G3H=8.53v PP3V3_SUS=3.30v PP5V_S0=5.06v U5110 1 PP3V42_G3H=3.40v 3 PP3V42_G3H_SMC_SPVSR=3.39v 4 SMC_MANUAL_RST_L=2.70v 5 SMC_RESET_L=3.36v 6 SMC_LSOC_RST_L=3.38v 7 SMC_ONOFF_L=3.39v 8 PP3V3_S5_AVREF_SMC=3.26v U7501 12 SMC_PM_G2_EN=3.39v 13...

ups... sorry I don't know.... :( PPBUS_G3H=479 3V3_G3H_RTC=367

big coils L9080= 407 L8102= 086 L7030= 447 L7690= 416 L7670= 421 L8410= 766 L6900= 364 L7702= 065 i have short to ground L7420= same L7410= same L7220= same L7210= same

hi, i have this board but don't turn on, I have tried to change the USB-C flex i don't have any voltage... F7700 is good PPBUS_G3H= 0 3V3_G3H_RTC= 0 PP1V8_SLPS2R= 0

Hi guys, I have a problem with this logic board, it works with battery (25 cycles) when disconnecting the magsafe it takes a few minutes and the computer turns off. With magsafe it can work all the time. In system information it recognizes the battery and the percentage goes up when it is...

ok nice the problem is C7234 thank so much !!!