(347) 552-2258 [email protected]

Search results

  1. A

    820-02443 5V 0.045A

    Found small liquid damage on R5710/11 which I missed. U5700/8 pad was fried. Restored damaged pad and replaced those two resistors and all works fine :) Gain. Many thanks :)
  2. A

    820-02443 5V 0.045A

    Tested on genuine 96W charger via USB C Very small liquid damage on UR660 and UF800 PPBUS_AON - 12.25V PP3V8_AON - 0.68V (0.144V in diode mode) PP3V8_AON goes to UR660 which was affected by liquid so I removed UR660 but still got only 0.68V All LDOs on all CD3217 are correct in diode mode...
  3. A

    820-00840 5V 0.05A on charger

    Checked signals and voltage and all was OK. Replaced SMC and all works fine. Many many thanks for all the ideas :)
  4. A

    820-00840 5V 0.05A on charger

    R5320-22 are good.
  5. A

    820-00840 5V 0.05A on charger

    Yes, got 1.1V that on powered port.
  6. A

    820-00840 5V 0.05A on charger

    PPBUS_G3H with charger and battery connected 11.51V (20V and 0A on charger) PPBUS_G3H with Battery only 11.50V LDOs on both CD3215 are both the same and correct in diode mode and voltage.
  7. A

    820-00840 5V 0.05A on charger

    C7050 - 0.06V SMC_USBC_INT_L - 0.005V
  8. A

    820-00840 5V 0.05A on charger

    Cant find any corrosion on board. PPBUS - 0V (not shorted) PPDCIN_G3H - 5.2V BUF_SMC_RESET_L - 3.4V SMC_RESET_L - 3.4V PP3V3_G3H - 3.4V LDOs value on both CD3215 are correct. TBA_AUX_DET - 1.28V TBA_VDDA/P - 5V PPVIN_G3H_P3V3G3H - 4.78V PM_EN_P3V3_G3H - 5.05V Flashed U2890 but no luck. Any...
  9. A

    820-01041 boot loop

    Restore successful. All works fine with fresh system. Many thanks :)
  10. A

    820-01041 boot loop

    Target Disk Mode successful - data copied. Restore in DFU then?
  11. A

    820-01041 boot loop

    820-01041 bootloop Client said he just close the lid and went for launch. When come back there was black screen and boot loop. There is boot loop even when lid is closed until battery is flat. Client need data and it is detected in DFU but every time during 'Revive' it will reboot so device...
  12. A

    820-00239 Touch Bar not working when internal mic connected

    Yes, when J6200 disconnected all works fine (did 5 resarts) Tested with known good Touch Bar and new flex which is connected to J4401. With J6200 disconnected all good (did 5 restarts) With J6200 connected but not fitted to palmrest and all good (did 5 restarts) With J6200 connected to the flex...
  13. A

    820-00239 Touch Bar not working when internal mic connected

    U6200 replace and same issue. Touch Bar works fine until first restart. Any other ideas?
  14. A

    820-00239 Touch Bar not working when internal mic connected

    So Touch Bar was not working. Disconnected flex and checked J5100. Found short on on pin 20/21 PP1V8_DFR. Removed board checked one more time and short gone. Diode mode in correct value. Turned on the MacBook and Touch Bar was working fine. Did a restart is gone again. Same short...
  15. A

    820-01814 20V on one side, 5v on another side.

    Traces from UB090 to the rest of components are good. Reflash of UB090 helped. All works fine :) Again maaany thanks :)
  16. A

    820-01958 20V and 0.024A-0.085A from charger.

    BTW there was no need to do restore after reflash. All clients data was still there :)
  17. A

    820-01958 20V and 0.024A-0.085A from charger.

    All good after SoC ROM reflash - thank you veeeerry much :)
  18. A

    820-00840 distorted image

    Yes, on boot menu as well. Thanks anyway
  19. A

    820-00840 distorted image

    Yes, the same
  20. A

    820-00840 distorted image

    Board got liquid damage on U7220, R8400, U8210, U8400. It turns on but image is distorted - I can see log in screen. R7226 and C10CA was not looking great. So replace that with U7220 just in case. Issue is still the same. Changed LVDS and tested with known good display and same issue. Tested...
Top