Search results

With a charged battery i did a DFU revive. This time i get logo on screen and loading bar with Host mac still halfway at "installing Software" the target mac was on and not charging. Didnt enter DFU with KB and had to jumper it. With Device on andCharger Connected (20V and 0 Amp Draw)...

Got hold of a charged battery. Now what should i do?

LID is okay. Backlight and Sound go off when lid is closed. HWMonitor shows "Memory Proximity" and "HeatPipe" at 128 C

R8070 is a No Stuff point on the board. Ran a jumper. now i get voltages and the macbook turns on detecting the SSD. Is this the permanent solution? Also fan spinning at max continuously but nothing heats up as such. When LID is closed it will not go to sleep and will shut down after 1 minute...

Pin 1 is 3.3V Pin 2 is 0.4V Pin 3/4 is 3.3V Pin 5/6 0V Pin 7 0V

There are no shorts on U3710/1 as well. But voltages are 0V

Both are 0V at both ends

Apologies Pin 2 is 0V. PP3V3_S0SW_SSD is also 0V (No Shorts) R3742 Resistance is 120k Ohms and rising.

12.5V on a Macbook Air ?? Are you sure?

Pin 1 3.4V Pin 2 3.3V Pin 3 3.3V Pin 4 0V Pin 6 0.4V Pin 7 0v Pin 8 3.4V

As instructed i replaced SMC as well. still the same. PPBUS is 8.2V without battery.

Replaced U7100. Still AMON/BMON missing.

82-00165 Device came in with intermittent hang issue. Turned it off and now it wont turn on. Will give the question mark folder. Green below U5110 and U8010. Replaced both. Still the same Checked U3740 No Shorts. P3V3SSD_VMON 0V SSD_RESET_CONN_L 0V SSD_CLKREQ_CONN_L 0V SSD_PWR_EN 0.5V

Battery Bus SCL/SDA is .500 Diode Mode to ground. Let me try and get back to you

Resistors are fine and the traces too. Heating the PCH only option?

Battery Bus (Diode to Ground) Pins 1-3 OL Pins 4/5 .500 Pin 6 2.7 U7100 Basic Voltages CHGR_VFRQ 3.3V CHGR_SGATE 15.6V CHGR_AGATE 6.7V CHGR_DCIN 16V CHGR_ACIN 4.3V CHGR_AMON 0.2V PP3V42_G3H 3.4V CHGR_RST_L 3.3V SMC_BC_ACOK 3.4V CHGR_BMON 0V CHGR_CSO_N 8.1V PP5V1_CHGR_VDD 5V PP5V1_CHGR_VDDP 5V...

SMC_RESET_L 3.4V WIFI_EVENT_L 0V SMC_WAKE_L 3V SMC_EXTAL 1V SMC_XTAL 1.2V PP1V2_S5_SMC_VDDC 1.2V SMC_TCK IS 3.4V SMC_TMS 3.4V SMC_TDO 3.4V SMC_TDI 3.4V PP3V3_S5_AVREF_SMC 3.3V

PLT_RESET_L does go high to 3.3V. What do you mean by SPI Bus Termination Resistors. Please guide

Device came in as not charging. PP3V42 was shorted. PPBUS was 0V with no Shorts. Injected Voltage and SMC was heating up. Replace the SMC. Now i get 8.2V at PPBUS and i get 3.4V at 3V42 but still no Mgsafe light and not turning on. PM_SLP_S4_L and ALLSYSPWRGD are missing.

Device came in for a not turning on issue. It has no Magsafe Light and PPBUS at 8.18V Some corossion at SMC. Removed. Jumpered a few pads. Installed a new SMC. Still no change. SMC_AVREF was missing. Repaced U5110. Now i get fan spin ( at max because SMC needs programming as the donor board was...