Search results

Clean board, stuck at 5v. I checked the LDOs lines of the CD3215 and everything is normal. I found a short on the PP3V3_G3H line, trying to find where the short was, the board started working again and the short disappeared. 10 minutes later it stopped working and the short came back. I...

Board resolved to work again. Waiting to see if it stops, to do the tests you asked for.

No problem history. The Mac worked perfectly. The PPBus always has 13v, even dead. Battery charged normally during the two days of testing.

Very strange board. Mac arrived dead, but always with 20v. I disassembled it all to check, when I tested it, it worked. The board is perfect. I built the Mac, tested it for 2 days, now it stops working again. When I don't work on the board for a few minutes and the charger connector, from 20v...

can you help me with SoC ROM? My first time with this process. I searched the forum, read about different adapter because of 1.8v.

Error DFU: Gave up waiting for device to transition from DFU state to DFU state. [com.apple.MobileDevice.MobileRestore – 0xFCA (4042)]

Logic board is perfect, no oxidation. Recognizes in DFU mode but does not complete (revive and restore) PPBUS_G3H - 12.30v PP3V3_G3H_RTC - 3.3v PP5V_G3S - 0 I checked the U6960 pin 11 - 12.30v pin 10 - fluctuating between 10 and 11.8v pin 13 - 5v pin 5 - 0.8v changed the U6960, voltages did...

I connected the cable the wrong way. It didn't report any failures.

I bought the S-UEM2 device and decided to go back to work on that abandoned mac. It showed changes in some pins of the UB300 (31, 33, 40, 42), as it had already been changed, I tried to change it again.

I didn't use it, I didn't have a C version. Do I solve that first?

I tested removing the CMOS. Bad U7600 voltages. I'm going to put only the pins that have voltage. - 4 - 5v - 5 - 5v - 6 - 0.3v - 7 - 0 - 12 - 4v - 15 - 4.6v - 17 - 12v - 18 - 5v - 24 - 0.5v I replaced the U7600 and the problem continues. No LEDs.

Device dead, no LED lights up. I tested with another source and nothing. I have PP12V_S5, but on Q8470 pin 4 (FET_EN_P12V_S5_R) has 10v, so I changed Q8470, but it didn't change pin 4. I don't have this new component, I removed it from another identical board. Any tips to find out if the...

You are magic! Mac working again! Now I'm going to test! thank you very much!

After changing Q7260/61, now I have stable 5v on PP5v_s5, L7260 and PP3v3_s5 line! But the board didn't turn on, is it because of the resistors I removed? Can I put it back?

During testing, a short appeared on the U4800, but it wasn't the problem. I compared in diode mode the L7260 (0.420) and the PP5v_s5 line as well (0.520), both equal to the good board. I keep the R7911/12/14/78 outside, right?

yes, I removed them all! I have no pulse on the L7260

nothing friend! I removed the components you mentioned and the same thing! this board is crazy! When in doubt, I changed the R7267/68 or u7200 again

I found something strange! R7267/68 that I had tested, now they don't go up to the correct value. They stay at 5k, so replace both. They were OK, I put the charger to test, it didn't work. They went back to 5k.

I had already checked these components, all ok. The R7367/68 would be the R7267, right? all ok L/Q7260.

I removed the jumper and the R7978. PP5v_s5 floated again and the L7260 is 0v