Search results

Hey. Have this board with liquid damge missing PP3V42. Obvious damage was under the heatsink bar leading to the fins which I replaced as well as U5010. I now have PP3V42 with a green light but only for a minute with 1 fan spin. In diode mode I get 0.088 but this seems to be getting pulled to...

Injected voltage on pn 1 of C0892 because I lost pad 1 on C1910. The board is liquid damaged and when I removed it the pad came off with the cap. I went up to 3.3 and no higher. The only thing very slightly warm was the CPU area. I also noticed that pn 2 on U1900 (PP3V3S5) is beeping to ground...

how much voltage? last time Idid this I blew up the cpu. lol

U1900 gets warm. Replaced it with new and replacement gets warm as well. G3H is 8.6V, PP3v42 is 3.37V, PPVRTC_G3H 0.157. pn 1 - 0.157 pn 2 - 3.307V pn 5 - 3.291V pn 6 - 0 pn 13 3.370V pn 14 - 0.7 Diode mode pn 1 - 0.01 pn 2 - .046 pn 5 - .049 pn 6 - .317 pn 13 - .296 pn 14 - .386 Thanks...

Put back together. It seems to be working again. pn 2 - 0 pn 7 - 0 pn 9 - .003 pn 11 - 3.297 pn 12 - 3.326 pn 13 - 3.309

R4851 and R4852 are within 33 Ohms as well. Areas are pretty clean. Aside from discoloration on via's. https://goo.gl/photos/qHkf4st1zWA4fJaW6 Thanks.

Hi. Thank you. pn 2 - 0 pn 7 - Jumps everywhere between .015 - .005 pn 9 - .003 pn 11, 12, 13 - Jumps everywehere between 3.3 - 2.7 R4850 33.8 Ohm R4853 33.8 Ohm Thanks again.

Hi. I have a 820-3437 with no Trackpad/Keyboard in Operating System except for power button. Both keyboard and trackpad will work pre - O.S. External KB/Mouse will work fine. Have tried with multiple Operating Systems. Thank you. Have a good one.

So I replaced U6201 and audio did start to work. After I shut it down and restarted it the audio did not work at all. I'm guessing that t isn't the chip itself but like you said a component around it because it seems like by heating up the area when I replaced the chip is what made it start...

Ok... I figured you were going to say that. :) Thanks. Have a good one.

Hi... All recommended components to check are good. I did have to replace DZ6700 and DZ6704 because the where both cracked but these are for audio jack. Other then that everything looks OK. Thanks.

Done. Thanks.

Had checked briefly what was obvious to me on U6201 before I posted. And saw someone suggest U6630 from a Google search. So I guess I was fishing. This is the same board that I just had the BL issue with U9600. Will check your suggestions. Thanks for the help guys.

LOL. Your probably right. But if you could tell me why the amperage had to be jacked up to get a small voltage output it would be helpful. Is the power supply bad. Because I tried it on a dead board that I dont care about and same shit happened. Also, I meant is it possible to do this repair...

Hi. pin 9 - 1.816V pin 25 - 4.49V pin 46 - 5.03V Thank you.

Not sure where to start here. U6630 ?

Reflow of U9600 worked. Thanks guys.

Hi, If you can please advise on the steps needed to carry out repair. Also if you can give me any insight on my fail to help prevent in the future. Much appreciated. Have a good one.

Tapping U9600 definitely effects it backlight. But doesn't seem to anymore then flexing the rest of that side of the CPU. Maybe that's the week point and anywhere I put pressure on that side of CPU directly effects u9600? Thanks.

LOL. I plead guilty to the 1st offense. I had bought the Wanptek KPS305D a while back, but never had to use it. Only tested with multi-meter. When I attempted to actually use it for a repair to find the short on PPBUS I had ground attached to a screw hole and voltage on pin 2 on F7040. I was not...