Search results

Hello, The device does not turn on, does not charge no liquid damage, 3V3_S5 : 3,3v PPBUS_G3H : 13v

VDDP: 0.7v C7075/77 and R7075 do not show any problems Why are we changing the u7000? What voltage is missing

P_IN : 5v AUX_DET : 1.2v SMC_RST_IN/ CHGR_RST_IN : No Voltage VDDA : 0,7v I don't understand P here CHGR_EN_MVR : No Voltage no standalone SMC_RST lineIt becomes NC_CHGR_SMC_RST_L but it has no connection to anywhere AUX_OK line It becomes NC_CHGR_AUX_OK and it says Unused PMIC Signals AMON...

I already said that there is no voltage in F7000 (pin1)

I didn't notice because I was distracted :) However, it would be better if you wrote what I should do.

Hello, no liquid damage, Same response on all ports, I tried all 4 inputs. I'm reading 5volts on PP20V_USBC_TB_VBUS. PPBUS_G3H no voltage. I removed the F7000 and there is still no voltage. I checked F7000 with ground, there is no short circuit. 3v3_G3H_RTC : No voltage

r7121-22, r7151-52 were defective, I replaced them. Also, c7374 had liquid damage and I removed it. It is currently drawing a stable 3.20 amps and charging. I'm testing it now, thanks

PPBUS_G3H : 10 volt U7100'ün 17/18 : 140 ohm 27/28 : 0,541 mega ohm The device still turns on and does not charge. it doesn't draw any amperage

Now the orange light is on, the device is turning on but it is not drawing any amperage, 0 ampere.

The device turns on, but it is not normal for it to draw 6-7 amps. It doesn't charge, on the contrary, it dies. It dropped by 5% in 1 minute.

I know what you mean. I know that the device decides how much current it will draw. But there is a problem with this device. The power supply output is set to max 7 amps, actually I don't touch it at all. When I plug the same battery into a working device, it draws 3.20 amps. When I plug it into...

SCL 529 SDA :525

hello, U7100 was getting hot. I replaced it. The device turns on, but there is an interesting situation. It draws too much amperage. For example, if I give it 4 amps, it uses 4 amps. If I give it 6 amps, it uses 6 amps and it shows like a short circuit. I think the q7130-35 before me was replaced

By the way, I can't see any images in the background.

I removed the RP842 resistor and connected it to pin 5 via UP900. I read PPVOUT_LCDBKLT 50v. Is this voltage normal or excessive? but still no image

I changed it to up700. but still the same PP5V_SW_LCD : 5v EDP_PANEL_1V8_EN : 1.7 volt

EDP_PANEL_1V8_EN PIN4 : 0.2 Volt 0,5,07, again 0,2 LPDP_INT_HPD PIN6: No voltage PP3V3_SW_LCD_CONN PIN 44: 3.2 VOLT PP5V_SW_LCD_CONN PIN 45 : No voltage

I bypassed and I get 3.2v PPVOUT_LCDBKLT_SW still no voltage PPVOUT_LCDBKLT : no voltage LCDBKLT_EN_L :12.4 volt PPVIN_LCDBKLT_R : 12.4volt

UP701 pin1:3,2 volt pin2:3,2 volt

hello, I hope you are well There is a startup sound and I can receive images via HDMI. There is no image on its own screen. up701 had exploded. I removed it. I don't have up701 as a spare at the moment, so I couldn't replace it. Can't I temporarily short circuit pins 3 and 5 on up701? I...