Search results

Device liquid contact the customer disassembled the device and LP610 exploded. I replaced the LP610. The device turned on. It worked for 1 day, then the fan started spinning at full speed and would not turn on. When I checked, I noticed that the UC710 was also damaged by liquid and replaced it...

Hello, Some water got into the Type-C port, and the sockets were in bad condition. I replaced all three sockets with new ones. The device turns on, but it doesn’t charge at all, and the charging indicator doesn’t appear. There is no other liquid damage on the motherboard or the device; it is...

hello, There is no liquid contact. I did not see any damage. When I put the 20v 0amp battery in, it draws 1.13amp but the device does not turn on. There is no short circuit in the coils P5VG3S_VSW :5V P3V3G3H_VSW : 3V

Hİ, I have a liquid contact motherboard. Sometimes the device turns on and sometimes lines appear on the screen and it locks and turns off. The UR600 was overheating so I disassembled it. I checked all the pins under it with gnd and I couldn't see any problem. My question is; Can I hear sound...

Hello, There is no liquid damage or anything similar; the board is very clean. It charges, and the fan spins. Without the battery, it draws 0.100A. In DFU mode, it fails at stage 4. The trackpad click works, but there is no voltage on L7430, L7420, L7410, L7210, and L7220. When I check for a...

Hello PLT_RESET_L : 3.3V CPU_VCCST_PWRGD : 1V CPU_VR_READY: 1V The green light is on. The fan is spinning. But it stays at 0.36 amps.

up800 area is liquid damaged. I removed CP810. But LUXE_C_VDD Line appears to be short-circuited. In this case, I need to replace UP800, right? There shouldn't be a short-circuit, right?

Hello, The device does not turn on, does not charge no liquid damage, 3V3_S5 : 3,3v PPBUS_G3H : 13v

Hello, no liquid damage, Same response on all ports, I tried all 4 inputs. I'm reading 5volts on PP20V_USBC_TB_VBUS. PPBUS_G3H no voltage. I removed the F7000 and there is still no voltage. I checked F7000 with ground, there is no short circuit. 3v3_G3H_RTC : No voltage

hello, U7100 was getting hot. I replaced it. The device turns on, but there is an interesting situation. It draws too much amperage. For example, if I give it 4 amps, it uses 4 amps. If I give it 6 amps, it uses 6 amps and it shows like a short circuit. I think the q7130-35 before me was replaced

hello, I hope you are well There is a startup sound and I can receive images via HDMI. There is no image on its own screen. up701 had exploded. I removed it. I don't have up701 as a spare at the moment, so I couldn't replace it. Can't I temporarily short circuit pins 3 and 5 on up701? I...

hello, Is it possible to disable the graphics card in the imac a1418 model and use it as uma?

Hello, I hope you are having a good day. the device came to the service due to liquid contact. When I received the device, it was running on battery, the keyboard was not working. There were liquid contacts on the motherboard. I cleared all of these. I changed trackpad flex. I changed...

The device does not turn on. I tried with a different battery. orange light is on. It stays at 0.04a amperage =PPBUS_G3H: no voltage PPDCIN_G3H_CHGR : 20v

Hello, A1708 820-00840-A device had liquid damage. C3405, C3400, C3306 I disassembled them. The device is turning on and charging. However, when I open YouTube or visual sites, it freezes, the screen turns black or crashes. Is this problem related to U3100/3200? Where should I look? I...

Hello, I'm reading a 15 ohm reading on the PP1V1_S3 (L8100). and the buzzer goes off. Could it be a dead CPU?

The device passes the test but does not turn on. I tried unplugging all the cables. Could this problem be caused by the video card? AMD

The device is charging, but the USB is not working. The USB voltage indicator does not light up at all. I tried using a flash drive, but its light is also not turning on, indicating that there is no USB 5V power. Where should I check next? I have already tested the DC socket and the intermediate...

hello, Battery is not installed. It draws 0.11 amps, then enters a continuous loop drawing 0.0 amps like this. The PP5V_S0 voltage fluctuates between 5V intermittently. It consistently behaves in this manner. PP3V3_G3H : 3.3v PPVRTC_G3H : 3.3v PP5V_G3H_LDO :5v PP5V_S4: 5v

hi, not poweron 0,02a stay P3V3SUS_EN: 3.3V PP3V3_S5 :3.3V PM_SLP_S3_L : NO voltage PM_SLP_SUS_L :3.3V PP3V42_G3H: 3.4v