Search results

I do get 1V1 J6100 Pin 32 0.713 Pin 33 0.395 I can't get to go into DFU. It was not even recognized when I connected the cable to the host Mac. I got a thunderbolt that can`t be used. I tried few different cables

I checked all the voltages are ok. The diode mode is around 0.500 on all

Hello, I am working on a Macbook air A1932 model that came with water damage around Q7660 which I already replaced. Symptoms are if I plug in the board only without a battery I get 5V 0.01A if I plug in the battery, I get 20V 0.02A I did the followings : Measured PPBUS_G3H, PP3V3_G3H Are ok...

All right, My apologies; I should have checked with a new screen. I found a broken screen but showing backlight. It Is amazing how the components communicate with each other. I kept thinking was a board issue. Thanks for everything.

UP710 from the schematics I see that is enabling the display, which is working; I went to UP800 is not giving any voltage on LCDBKLT_SW, this was replaced. QP800 I have 11.5V on pin 3 and 11.9 on pin 4. I am quite confused as I can't spot any other short or any reason why UP800 is not producing...

I get image, but no backlight. I have replaced the backlight driver but is same. I will check the signals as well shortly.

I have removed the short, and the MacBook is turning on, but now I get full fan spin and no backlight or touch bar on. Any help would be appreciated.

I found a line CODEC_WAKE_L going to U8100. It looks like a small burn. I am right? I do get headphones sound.

Hello, I got a MacBook air a2337 with liquid damage; the audio board was damaged, sort and no power, I removed the short, and then I got the MacBook back on after this sound was gone. I decide to replace the audio board, but the sound is still not working. Speakers are ok. The motherboard is...

Yes, confirmed the SLG4AP43605V( UP710 ) is shorted to ground. Now the issue is that I am unable to find this ic. Any hint?

I took out the UP700, and measured all the lines, but EDP_BLC_5V_EN is shorted to the ground. UP710 might be faulty?

I have injected 2v on LC320 and UP700 is getting hot.

Hello, I have received a Macbook Pro with no power. The device was affected by water damage, I fixed all the corrosion found, but it is still the same. The voltage is 5v and 0.05a to 0.08a slowly fluctuating. PPBUS_AON is stable 3V8_AON is 0.200V going to 0.400V. LC320 in diode mode is 0.009...

Thank you so much, I was thinking about this, but I wasn't sure.

Hello, I received a job with a very damaged board 820 3023-A and I decided to replace it as they were too many issues. After I have replaced the board I am unable to boot from the same hard drive that was in. The hard drive is working all right but it seems that I can manage to mount it or to do...

Hello, I actually have 87W charger, I will try today with 96W as well and reply back, thanks The voltages looked ok but I will also double check again.

Hello, I have a MacBook pro motherboard that is not turning on, this had the battery previously replaced. I have tried the following: Plugged in the charger is showing 5v 0.03amps when I go into the dfu mode is showing 20v 0.03 to 0.07, sometimes goes to 0.38amp. After I try to revive it, is not...

Hello, I have a very wired issue here, I have replaced an charging port on iPhone XS max, everything is working fine but after around each 2.5 minutes the phone is restarting. Here is what I have tried: I inspected the components on the board (they look fine) Took one by one each connector...

Hello, I have reball - ed the SMC everything is the same, powers on only if is plugged in, battery indicator is not showing noting, sometimes is turning on if I try few times unplugged. The battery is good and if I turn on is showing the percentage ok and the macbook is running fine. Any help?

In the case that is doing the same after SMC reball could you tell me where to look? Just in case. Thanks