Search results

  1. T

    820-00875-01 5v 20ma, liquid damaged

    ok so i have removed F7000 and checked voltage at C7050 and getting nothing there. I have also just checked LDO 1.1 and getting 0v there
  2. T

    820-00875-01 5v 20ma, liquid damaged

    PPBUS_G3H 0.38V 3V3_G3H 3.41V LDO's on both cd3215 read correctly, however they will read correctly for a few seconds, drop lower and then comeback on reading correctly again. This was tested with and without the battery
  3. T

    820-00875-01 5v 20ma, liquid damaged

    Hi. As the title suggests, i Have a macbook here that had suffered slight liquid damage. It came to me for a new screen as one of the screen flexes is torn, but on opening found slight liquid damage around the charging area and backlight driver area, im getting PP3V3_G3H_UPC_XA and XB. it will...
  4. T

    820-00687 doesn't do anything after battery change.

    guessing it will have to be a pulled one due to them being programmed? Thanks
  5. T

    820-00687 doesn't do anything after battery change.

    Sorry missed that one. thats reading 1.13v
  6. T

    820-00687 doesn't do anything after battery change.

    Hi. here are voltages. U7000: P_IN = 5V VR_AON = 3.31V VDDA = 4.82V VDDP = 4.89V POWER_GATE_EN = 3.27V ACIN = 1.26 ACOK = 0V CD3215 LDO's BOTH XA_LDO = 1.8V 3.3VXA_LDO = 3.27V
  7. T

    820-00687 doesn't do anything after battery change.

    ok thanks. ive replaced the cd3215 and short is no longer there. am getting 3v3 on PP3V3R3V0_AON however charger is still stuck at 5v 22ma this time. Checking ppbus_G3H im getting -0.134v, on diode mode im getting 0.405v. resistance to ground is ~265kohms. checked 3V3_G3H (L6995) and no shorts...
  8. T

    820-00687 doesn't do anything after battery change.

    which connector are we talking about to be careful of?
  9. T

    820-00687 doesn't do anything after battery change.

    On further investigation found PP3V3R3V0_AON to be shorted to ground @4 ohms. removed cd3215 and short has gone. Will order another and fit. Would a loose fitting usb port cause this? every cable seems slightly loose when fitting. Just weird why its failed for no apparent reason. cheers
  10. T

    820-00687 doesn't do anything after battery change.

    Hi. so short story, battery health was @ 55% capacity. before strip down the macbook would work, charge at 20v and didn't really appear to have any other issues. swapped battery and now taking no charge. was originally 5v 120 ma. after NVram and PRAM reset it went down to 38ma @ 5v. iv tried...
  11. T

    820-01598 HELP.

    pretty sure this is 2019 model. like i said with usb-c it doesnt charge or do anything. just sits at 5v 5-10ma. only way to charge the battery will be either via another macbook the same (dont have one)or charging it from my DCPS which im used to doing.
  12. T

    820-01598 HELP.

    battery is dead. i guess i can charge it using my DCPS to test this theory
  13. T

    820-01598 HELP.

    unfortunately i dont have one. i ordered 2 from mouser. both the same. however i think the issue is my using a little to much heat and the board has warped slightly. So annoyed with myself
  14. T

    820-01598 HELP.

    ok i did this and short has gone. i have replaced u2800 with one from mouser and now its worse, im now getting 5v and 10ma on charger with and without battery. getting nothing out of 3v3_rtc where i was before. loosing the will to live with this thing
  15. T

    A2141 doing odd things when on charge and lid closes

    So my personal Mac has been acting weird for a while now. I can use it fine while plugged in on charge. No issues at all. When on battery it lasts around 6 hours of continuous use. However-if it’s plugged in on charge (86watt charger) and I shut the lid, 9 times out of ten I have to hold the...
  16. T

    820-01949 no power

    Did you ever get to the bottom of this?
  17. T

    820-01598 HELP.

    a bit more digging shows that pin 3-4 on U8290 where shorted. now i still have 1.3 ohms on PP3V3_S0_TBT_X_ISNS_R but unsure if this is normal or not.
  18. T

    820-01598 HELP.

    ok no problem. so short removed from pp3v3_g3h, however my 1.3 ohms on the pp3v3_g3h_rtc is still there. connecting my psu up to it again @3v 2amps shows a heat signature coming from U2800. However it is faint given that is under a shield. Im a bit puzzled as when checking the RTC 3.3v line on...
  19. T

    820-01598 HELP.

    also do you think it would be possible just to link it out for testing purposes? afterall it is only a switch
Top