Search results

Board came in with short on U7650. Replaced with donor from another board and new chip both result in 5v only on PPBUS_G3H_CHRGR. Not familiar with these board. What to check next?

No just always hit reply when speaking to someone but my bad...

I assumed the lid sensor first, that it may think its not being opened up but the screen works properly otherwise which is why I didnt look at it further. I also didnt have a secondary board to test with so was unable to test if it resolved the issue but the screen would shut off and turn on...

This is my experience on this repair. Not sure of the root cause but this got it going without replacing major parts of the system. Issue: On boot up the Macbook has Trackpad and Keyboard function but if you close the lid it loses Trackpad and Keyboard function. When the Mac is put into sleep...

Still learning the M1 M2 power up process but here is what I checked and found New port Known good Apple Original 61W charger PPVBUS USBC1 5v PPBUS_AON 12.14V PP3V8AON_PH1/PH2/PH3 all 3.747V Poked around PMU found PP5v_BSTLQ_VOUT_MPMU shorted to ground Bad cap Line came up to 2.7V but still no...

a1502 Late 2013 Macbook Pro. Bios is dead. I have the serial but no tools to created a legit bios with matching ME info, Sys, etc. Serial c02mlmg3fh01

Nevermind Louis has them on the site lol

Are "new" chips not programmed? Finding parts boards for these with the ends not cut off is very difficult. I have B03 and this board is C00

Im not overly familiar with how this entire USB system works Liquid damaged board corrosion and burn pad on UB300 and corrosion under UB400. Reballed UB400 and swapped UB300 for good chip. Get 5v at fuse but wont go to 20v. Ive poked around and found a few 3.3v lines but not sure of what all...

Attached should be known good file https://drive.google.com/open?id=1ACfS2aIp0LR_ZXwZljmEeIzKr4ycqSKp

I removed the EFI Lock. Its been installing the OS now for about an hour but says 10 min left. Its running very slow. I assume the ME region is wrong. Where is Duke! lol

I put that on. It had an EFI passcode. I removed it no biggy. Its still running really slow. Starting to think its an issue with the SSD possibly? Although the mouse seems sluggish also so it seems like a Kernel Panic kinda of slowness.

Thank you. Anything helps. I just need to get this thing done so the owner can use it.

Id love to learn how to do this so I dont have to plz bro these.

Got a 820-3208 that had the bios swapped by someone and its running dog slow. I dont know how to clean the ME region or add the serial so needing some help. Serial Number is C02KL348DRV7 Sticker on board is C02317201KBF9DHAK

Not sure why my phone posted a million question marks. Sorry about that lol

I'm at home right now but before I left I checked 3v3out 1v1 ldo 1v8 ldo and some other power rails around those chips 1v1 was 1.08-1.1v 1v8 was 1.79v 3v3 out was 3.29v ??????there was one other 3v3 line that was also 3.29v the ldo voltages I believe were only present on 1 chip at a time...

5v at the Fuses by Q3100/200 which cycles every few seconds

No short between PPBUS_G3H and PPDCIN_G3H PPDCIN_G3H with charger plugged in is 5.12v constant Now PPBUS_G3H is 0v and voltage on the Coils USBC_X_CC1, etc are bouncing around 1-2v

820-00840 Liquid Damage Liquid was around and down both USB C charging Circuits and controllers Cleaned area and found 5 burnt traces Burnt traces R3351 Burnt PPBUS_G3H pad - Ran jumper to R3451 PPBUS_G3H side and replaced R3351 with new 10K resistor R3360 Burn via - Cleaned and checked...