Search results

I have checked pin 1 sorry, pin 3 is 1.75V

Both removed, always 0V Should I proceed with purchasing a new diode then?

sorry, sometimes the page doesn't update with new answer. Here are the measurements: Pin 1 0v (or -0.10v) Pin 2 5.19V Pin 3 1.75V

is this okay?

black pointer on pin 2 pin 1 1.24 pin 3 0.23 black pointer on pin 1 Pin 2 0 Pin 3 0.94 black pointer on pin 3 Pin 1 0.23 Pin 3 0 This is without power supply

R6906 0.28 Do I measure the D6905 with black to ground? If these are the values: Pin 1 3.7 M ohm (it is worth very unstable) Pin 2 118k ohm Pin 3 0.427k ohm

I corrected my previous post, I had done the measurements with the power supply connected. If there is a need to remove them from the board I will do it, it's not very clear to me, sorry

PPVIN-G3H-P3V3G3H" Diode mode 0 R6906 Diode mode 0 resistance 0.28ohm D6905 ppbus_g3h 0.424 D6905 PPDCIN-G3H-CHGR 0 D6905 PPVIN-G3H-P3V3G3H 0 I realized that I performed the measurements with the power supply connected, without it all the values are completely different and therefore I rewrite...

V3V3 G3 H- boost 0V PPVIN-G3H-P3V3G3H 1,75 V V3V3G3H-SW 0V Agi ND-P3V3G3H 0V V3V3G3H-BIAS 0.04V V3V3G3H-FB 0V PM-EN-P3V3-G3H 2.67 V

U6990? Why can't I find what you indicate...

1v1_LDO is 0V XA and XB PP1V8_UPC_XA_LDOD 1.78V PP1V8_UPC_XA_LDOA 1.78V PP3V3_UPC_XA_LDO 3.28V

Pp1v8_upc_xb_ldod 0.48 website 0.48 Pp1v8_upc_xb_ldoa 0.53 website 0.52 Pp1v8_upc_xa_ldod 0.48 website 0.48 Pp1v8_upc_xa_ldoa 0.52 website 0.52 Pp3v3_upc_xa_ldo 0.51 website 0.50 Pp3v3_upc_xb_ldo 0.51 website 0.50

The problem occurred suddenly while the computer was on, it shut down and from there no sign of life. Original charger. Tomorrow I'll try to take other measurements, I don't have a good board for the values...

hi everyone, logic board with no sign of liquid, no ignition, I receive 5 V on the PP20V_USBC line but nothing on the PP3V3_G3H line

Sorry, I didn't see the answer and I had updated my previous post, with the new capacitor everything worked! Thanks for the support 🤝😊

yes, I had already dedicated myself to this resistor, with the tester measuring 0.18 ohm. 3V3_G3H_RTC is 0V but I didn't replace C6961, I diden't know if this could be the cause even if I see that it is a capacitor connected in parallel to others. Update: I soldered a new capacitor and it works...

PPBUS_G3H in short Update: C6961 is in short, now I have 12V on ppbus

PPBUS_G3H and 3V3_G3H_RTC?

All 0V, I corrected the back post above because I didn't remember the names of the lines I had checked. I think the problem could be U7000 but I'm waiting for your expert opinion.

No 12V, no 3V, all the lines don't seem to be powered Could the U7000 be faulty? PPBUS_G3H I have 0V