Recent content by WeLoveApple

  1. W

    iPhone 6s wont turn on

    In the meantime I found the problem. I started changing the caps on the PPGPU rail and after a while it started working again. :)
  2. W

    Iphone 6 no service

    In initial state phone was only searching for service. Then I changed U_DSM_RF. Now it stop searching after a while and then it just stops with no service. Any ideas what should I do next?
  3. W

    820-3435-A no image on internal display

    No history. It does not seem to have liquid damage and corrosion. There is image if I connect an external display. Though it freezes at half of boot. Also I could not seem to able to boot from external HDD. So it seems a bit more complex. I am not able to test with another LCD. Where should I look?
  4. W

    820-3476 wont turn on

    I did connect it. It will recognize the battery but wont charge it. OSX status: "Replace now ".
  5. W

    820-2610 no green light

    Any further suggestion?
  6. W

    820-3476 wont turn on

    This is weird: The board stayed some days put aside: now it works perfectly. Tried in in the case and everything seem to work. But this time I was afraid to connect the battery. Last time I connected it the green light and all the rails went to 0. So it is possible that a fried battery would do...
  7. W

    820-3476 wont turn on

    Coffey spill. But board did not get too much damage seemingly. Only obvious thing was a cap (C1910). I changed that. After that it did catch green light, it even started okay with lcd. Then I connected the battery (which had corrosion before on the logic board part ). After that the green light...
  8. W

    iPhone 6s wont turn on

    No liquid damage or anything unusual. It was sucking around 0.2A. Changed U2. After that 0.6-0.7A. Still wont turn on. Measured important power rails that go in and out of PMIC. Most of them are okay, except: PPCPU is 0.5v instead of 1v PP_GPU_SRAM is only 0.15V PPGPU is missing. I did measure...
  9. W

    24" Imac very slow boot

    I can not boot into ASD.
  10. W

    iMAC wont start

    A1224 (EMC 2210) It wont start at all. Only first diag led is on. When I want to turn it on the fan spins up for a second (quarter fanspin style) and at the same time the second lend blinks one time. Tried with another good power supply. It does the same. Ideas?
  11. W

    24" Imac very slow boot

    A1224 (EMC 2210) IMAC boots extremely slow (45 minutes). Tried with another HDD, hdd cable, external hdd and ram. Same issue. Any idea?
  12. W

    [SOLVED]820-2915-A no backlight

    I changed LP8550. (not working the backlight) PP3V3_S0 directly to LCD_BKLT_PWM(working) Thank you! Maybe the smc.
  13. W

    [SOLVED]820-2915-A no backlight

    LCD_BKLT_EN 3.32V PPBUS_SW_LCDBKLT_PWR 12.58v LCD_BKLT_PWM is 0V SMC_LID is 3.4V with lcd :I :)
  14. W

    [SOLVED]820-2915-A no backlight

    Yes. Tried with flashlight from back.
  15. W

    [SOLVED]820-2915-A no backlight

    No liquid damage. SMC_LID is 3.4V LCD_BKLT_PWM is 0V LCD_BKLT_EN is 0V PPBUS_SW_LCDBKLT_PWR is 0V Tried with another LCD too...
Top