For $29/mo, we provide access to advanced level technicians who will answer your questions on any Macbook board related matter to the best of their knowledge promptly & walk you through how to solve your problem so you can deliver a working board to your customer.
Appologies, you are right. Its 50Ohm for both.
I am missing PP3V3_S5_POLARIS when the kit is connected? Both with USBc and power adapter into it connected. Wouldn't this be fed from the data kit when lifeboat connector is removed?
PP1V8_SSD_DRAM = 0V
Shall I keep measuring the rest?
Seems serious overheating, all battery cells boughed up.
PCH decapped
Tried Apple Migration/data transfer kit and cant detect the SSD neither in Disk Utility nor on boot via the kit.
Short on the PP3V3_S5 side, but with removed lifeboat PP3V3_S5_POLARIS reads 0.75Vdc
All point on the SSD...
Replaced R5100 with 10K, SMC_RESET_L went up to 0.15V but that's it.
Diode mode on SMC_RESET_L is 0.505Vdc
No corrosion on J6100, there was only around the SMC
U5110 seem to get the voltages it needs. Replaced it but still SMC_RESET_L stays at 0.12V
Also replaced U7100 thinking that it might have internal failure and might be pulling SMC_RESET_L down, but no difference still SMC_RESET_L stays at 0.12V
Diode mode of U5110 aligns with a spare board i...
Corrosion on R530/31 Replaced both and repaired the PP3V3_S0_EDP_SW trace.
Reflowed the SMC to ensure gunk removed underneath.
Still no current draw at all. No shorts. Tried to bypass SMC.
from aliases table voltage stops here
PPVRTC_G3H = 3.4V
PP3V3_S5 = 0v
PP5V_S5 = 0v
No pulse on...
I am having the same issue. Reballed the rams 2 times and still 3 beeps.
Can it be a faulty ram IC? No liquid damage or other visible problem.
If RAM IC failure, can I swap randomly from A1466 ?
Tested with a spare board, which is not turning on, but I'm sure HDMI part is OK as no liquid there.
LPDP_INT_HPD Not sure how to test with screen connected?
With disconnected screen
LPDP_INT_HPD = 0.6V - when charger is 5V/0.5A, then 0V when chimes and switches to 20V
Turns on with a chime noise, capslock responds. No picture on internal, HDMI or USBc videos outputs.
Can see it appearing in apple configurator. Seems to be turning on.
Milk coffee liquid damage via the HDMI port. Mainly around UT520, HDMI port, QH501/2, UH502
PP5V0_HDMI_DDC_CONN - 5V...
Found it, thanks @2informaticos. Seems bridge was shorting the line.
Although no corroded pad or heavy liquid signs, SMC replacement resolved the initial issue.
Not sure why but now I get SMC_RESET_L = 3.39V, but it ws still 0A power draw.
I went and touched up the resistors around the SMC as they had some minor oxidation appearance.
Now I get 0.18A, no fan spin. It takes a while until it starts pulling any current.
I get around 45*C / 30*C areas on...
Not turning on, managed to turn it on after cleaned little bit of oxidation around SMC and with SMC bypass. Worked for a bot and stopped turning on.
No current draw
PPVRTC_G3H = 3.41V
PP5V_S5 = 0V
PM_SLP_S5_L = 0V
No visible short or damaged traces/components
This is board on its own only with power and usbc to another mac scenario. Each time I pull power out it switches off as no battery.
Using FORCE_DFU pads I can reach DFU mode, just failing with that error.
Need revive as its a data recovery case.
Haven't seen this error before. Some places says bad cable, changed the USBc socket, cable has been serving me well with other restores.
logi.wiki says its = 75 - T2 booted in recovery mode (Revive wont work). -...