Search results

Ok, pp3v3_s5 is present on L7220= 3.3V there is 5v on l7260 but it is like pulsing. The first time you take the measure it is 5v but later in 5 seconds it drops till 0,005 mv or something like that

Everybody says that is BS but the best investment that I have ever made in my life is to buy a blender juicer. Since I have it and I use it I feel better, more energy, healthy, If I get sick, I drink more green juices, and healthy again (knock on wood :D ) The recipe that I take everyday 3...

It depends on Louis or Duke to create a sub forum for this. I think is important.

I have found this one http://www.amazon.com/Tjernlund-M-6-...ds=fan+460+cfm 460cfm Did you find the main filter cheaper mnaty?

Yep, smaller and longer probes than the originals that any multimeter comes with.

No Title One thing that works great is cheap probes, you can buy them and then attach needles to the tips, first scratch a little bit with something the tips, apply some flux and then join the needle to the tip and and solder with the tin. They work very well you can buy a pair for less than...

Ok this has no fucking end :( The R2179 I replaced it and it is giving me the same value as before, ok I checked a cap c7772 was shorted, I replaced it and now the R2179 is giving me 282.5 Ohms instead of 2.2k :mad: Pin 11 is giving me in diode mode now 0.102 V better than before (0V) I need...

Ok I´ve measured in diode mode the u2600 and in pin 11 I have nothing so I look the schematics and I look for the =PP1V8_S0 I have found that R2179 is giving me a wrong value instead of 2.2k I got 0,005 Ohms Im going to replace it and check, that little resistor can cause the machine to doesn´t...

f7040 = 12.55v

Yes it worked not very well... but now it is not :( I had to change u2600 because it was corroded too, and probably is the problem Im gonna to try fix this mofo mobo, all help is welcome :D

Also I had an issue with the u7940 was shorted, I already replace it and it is not shorted now, I have green light and orange while charging but when I try to turn on....nothing!! no fan spinning...nothing Shorted pads...nothing the u7000 gets a little bit warm and Im not sure if it is shorted...

I had the same idea because I have a window on my right side, but the problems for me are: 1 if one day is windy and cold the room is gonna be cold 2 if it is windy could all the fumes come back inside? (too difficult but not impossible) 3 if you need to move to another location. 4 Drilling...

Sorry be patience with a newbie :o I have 16,78V on pin 3 with AC connected

I agree with you. I think probably the sensors are because of the fan speed, but I don't care about the sensors, once a month we change the pre filter like Louis does and we don't need the sensors and too many electronics. I prefer the easiest way to do it. You can put a stick that says the...

Good info mnaty. The best choice would be buying the hakko pre filter and main filter, the main one has the carbon one included at the bottom. So the fan would be before the filters, isn't it? One thing I know is that the air that goes in has to go out but I don't know where it goes in the fa 430

No Title Ok I have received the q5490 but it is quite strange, I´ve soldered one and in diode mode the values are: PIN 1: 0.00 PIN 2: 4.67 PIN3: OL PIN 4: 4.15 PIN 5: OL PIN 6: OL There must be something wrong, did I put the mosfet in a wrong orientation? Could somebody give me the correct...

Virtual Life said: "If anyone has schematics for it it will be great. Or just a High resolution photo of the S6 Edge + Logic board from both sides" You are welcome mofo :cool:

Great!! This one is gonna be better than a professional one :cool: Also we need 3 filters Prefilter, Main filter (Fiber glass paper) and the last one a carbon filter, like the professionals are made.

I´ve found this tips for the noise https://www.youtube.com/watch?v=W2D15m7MD40&index=1&list=PLcuY6o67S8_3-2C3ZY5BZ9nE5UPeJEdKF

The fans has their own controller. I was checking for the hyperfan http://www.amazon.com/Hyper-Fan-Hydroponics-Ventilation-Circulation/dp/B00JGCCKEM/ref=sr_1_2?ie=UTF8&qid=1459794734&sr=8-2&keywords=hyperfan but these ones are better and cheaper. What about the hoses? I´d like hoses like the fa...