Search results

3V3_S5 is present at 3.3v. Didn't checked 32 kHz, I will check and confirm it with O-scope and new U2800. I found something like 0.6v wich I think should be more around 0,4V... I will check also PM_SLP_SUS_L. I found diode mode on PP3V3_S0 very low 0.050. with PP3V3_T29 full short to ground...

So back to the board, Ireplaced smc, and got 12,56v on ppbus_g3h. It's turning magasfe light to orange when a battery is plugged. However board still doesn't boot (no fan spin). I found U2800 with a small hole crack, all signal were present except PP3V3_T29. witch is total short from ground.

Thanks for u9310 clarification. And sorry for the basics info i forget to tell. Yes R7000 is 0 ohms with continuity to u7000, I can see also 3,46v on both sides and U7000-Pin13 Resistance to ground R5280 2,611 kOhms R5281 2,614 kOhms Diode mode also checks ok after changing the shorted ISL...

No water damage, received this board initially with no green light it was also missing U9310.. PP3v42_g3h was 3,42v SMC_BC_ACOK was also 3.4V sys_onewire and adapter_sense = 3.3V. It turned out smc data line was shorted by isl... Replaced ISL and got green light with ppbus_g3h at 12.23V :( I...

I got this board witch has been messed with a little...It got a sticker with (bad video card/Bios) Hopefully GPU has not been reflowed. I took a look at it and here is my findings: Initially quarter fan spin...nothing to do with charging sense resistor L3508 completely burned...but thats not a...

A shorted rail can also do this issue. Did you check all rails, the one that are cycling with the fan goiing on aan off aad the one that are steady.

Ok It is solved, done with that board. It turns out my 3 years old 2 pin speaker test died, Thanks for everything.

Thanks 2informaticos! that helped at least locate the issue, backlight was ok without the i/o cable. SMC LID was low because of...keeping my test speaker upside down with its magnet just beneath the sleep sensor. What a total troll... Now I don't have audio, I mean it's not disabled, i see the...

Thanks for the suggestion Gmorb. Yeah it was powering on both with only charger or only battery. But there was no syswire communication. It's fixed, somebody had used brutal force on J9500, as sys_onewire pin was moving, same thing for SMC_BC_ACOK. No corrosion at all, clean board... Didn't...

It was really missing, now I have back smc_BC_ACOK 3,3V at pin 1 of J9500, but still no magsafe light. I doubled checked the connector even in the internal pin#1 and I get 3.3V... Still investigating..

Oh wait a second, smc_BC_ACOK is actually not present at pin 1 of J9500. I will report shortly.

I found this one a little tricky, no corrosion. I have no magsafe light at all. PP3V42_G3H = 3,41V, PPBUS_G3H, = 8,6V, SMC_BC_ACOK=3.3V, present at I/O board J9500 connector SYS_ONEWIRE=3,4V present at I/O board J9500 connector.. ISL6259 pins 17,18= 5ohms, 27,28=22ohms. DCIN 16V and ACIN (4.xV)...

Fans gradually ramping to full speed is usually related to TS0P, since TS0P sensor is located in the trackpad, either bad trackpad, bad trackpad cable or bad traces/pins on J4800. When SMC can't read trackpad sensor temperature it ramps up the fan. In your case I am sure it's your connector...

Did you check R7402 / R7403? check for corrosion traces and measure good value.

PCH_SRTCRST_L should be higher around 3.3V Check if R1802 measure ok, hard for a 20 kohms to go high but still possible it happens. Check also if any corrosion underneath the resistor ( I mean corrosion on the pad). Check also C1802. See if any short on pin 2 of R1802. It could be a pch issue...

I got trolled today with an early 2013 retina not seeing ssd, PP3V3_S0SW_SSD 3.3v was showing at both side of L3700. But L3700 was high resistance, pratically no current flow. Replace and everything ok. So check L700 jus in case.

Long time i didn't work on these boards, I simply checked on the schematic, but i don't have a board in front of me to confirm. Maybe it doesn't exist. Sorry

Look at U7740, it has pp3v3_S5 input on pin 3,4,6 and PP1V05_S5 on the output pin #1. 1) if you have a break in the traces and pp3v3_s5 never reach the input of u7740 you will never have PP1V05_S5 at the output. So please check pins 3,4,6 2)if pp3v3_s5 is present at pins 3,4,6 of u7740, remove...

I stopped working on this board, first time I encounter this issue next time I will not spend that much time;( Thanks for your help and sharing your experience.

Thanks! Awsome, it works great and ASD EFI passed. Before it did'nt found the override file because only system and mlb serials were changed... Now all is good. This post can be marked solved!