Search results

Found a short on PP3V3_G3H_VDDMAIN Inside the U7800 chip (tested with multimeter on its pins).. I don't have a donor board for this unfortunately, are any other boards' calpe chips compatible?

Am struggling a little today with this board and need some clearheaded suggestions; had a couple in a row and can't think straight:) Board might have had some work done on it, but i think i spotted all the mistakes (some coils of PMIC were taken off, but so far i don't know why, nothing else...

OK i cleaned and rechecked all my work, apart from a tiny bit of adding solder to R3078 pin 1 which seemed loose, didn't do anything, and of course Now everything works. Knew my CD3215s were good!

OK after looking at all LDOs, CC lines (and seeing nothing off) I decided to also replace the other 3 CD3215s since i had a fully working donorboard with 4, and i wanted to take a shortcut i guess: My results now at the different ports: UB300 5V 0.3A, bootlooping, all LDOs high UB400 5V 0.0A...

Sounds good man, hope you do. always wanted to go there, love the medditeranean sea! Have fun and relax! Yeah you're right i'm going to do some measurements and let you know how it goes.

Long time no speak, how are you Vali? took some vacation? Have a 820-00928 here that came in for no power/5V on all ports Saw a blown diode at DB504, which helped me suspect UB300 (also, it lit up under thermalcam) : replaced UB300 with a good CD3215. Now my results are as follows, when...

Yeah I’m pretty sure my resistance measurement was correct and was surprised it took that high voltage to get to about 1amps.. My psu might not be very accurate. damn I don’t like no-fixes

Jesus.. im sorry, my bench-mat was still hot from work i did earlier, so the heat around U2800 was coming from that. I was using shit-wires before, changed those, I injected about 2.8v maximum, it was taking about 1A and only the PCH-side of the CPU is getting hot..

diode mode readings on the entire J6100 all look perfectly normal (i used openboarddata for reference, all datalines match up with those readings) Tying FORCE_DFU to 1V8_SLPS2R didn't change anything by the way. I realised i didnt completely finish diagnosing correctly yesterday, probably was...

Need a little help, if you don't mind. This board was liquid damaged, but very minorly: the audio board looks like it took a hit on it's audio amp chip. the main board looks pretty good, with just some minor spots around U7290 and Q7291, replaced the whole area, controller, buck and affected...

OK so it definitively charges the battery. Customer wants it back now, so this one is going. The board is working, but i don't understand how PPBUS can be 12.00V without the battery...

pfff battery is at 100% right now, so no charging is going on. will have to drain the battery a bit to see if its charging, will get back here. so far, everything seems to be working normally, just that low ppbus voltage is bothering me

Need a clear mind on this, been spending way too much time on this board PPBUS_AON on this board measures 12.00V I thought this has to be 12.6V on this board, right? What can cause PPBUS to be too low? Strange thing is, the board boots and works fine (i only don't have trackpad connected...

Yes. makes sense, learned a lot with this one. Thanks again!

OK some good news: and a little info on what i found, it might be of help to others later on: After i put back original U4770 dump and tried DFU again, it was still painfully slow. I managed to boot it into Internet Recovery with the help of an ethernet-cable (progress) but still extremely...

OK, so i have tried flashing U4770 with a new ROM Dump i found on one of your other posts ( https://boards.rossmanngroup.com/threads/a2141-820-01700-05-no-power.63469/#post-95679 ) With this rom dump flashed, i cannot complete a DFU Restore, it hangs and says takes too long to transfer from DFU...

what fault did you find exactly?

Yeah you’re right..Pfft ok will update tomorrow, thanks for your clear mind..:-)

God I fucking hate T2-boards.. Today I’ve replaced ua600 because it still looked dodgy. Ultrasoniced it afterwards and still this thing is slow as hell, did dfu restore twice, all to no avail… Will check in here tomorrow, I also found online while googling that these -2003F errors seem to be...

OK, tried to do as you suggested: Machine wont start in Diagnostic, when holding D at startup, it wants me to connect to WiFi and then says Starting Internet Recovery for longer than an hour, ending up on error -2003F It does the same when i try to boot it using ShiftOptionCmd-R, same when...