Search results

If anyone could suggest me how i can troubleshoot it and test if it is somehow working that will be fantastic. The visual is good and i have microscope to look at the logic board, but if there any other way too it would be wonderful. Thanks!

Is there anywhere Macbook Pro 13 Retina 2016 schematics? The model is 820-00875-A. I got water damaged 2016 model and i want to fix it. It is so stupid that there is no light indicator that tells me if its somehow working...

The battery was shit. Bought a new battery from here, works great and as good as the original battery. Thanks everyone!

What should i do next?

dukefawks You are getting angry quite fast. First of all i have already answered your question. There is no need for getting angry. Check the page two for the answer.... if your not up to it. I will copy it for you. :) No i have not. Now i measured it. F7140 PIN 1 = 0.5 volts and increases...

I already checked the R7050. It is 10K Ohms and there was 0.1 volts. When i checked the R7050 with diode mode it was 2.116 from both sides. And J7050 is good. I have checked if there was under it corrosion but there was not.

at first when i checked the PPBUS line with diode mode it beeped really long and it started from 1.000 and went down to 0.146 and after that it did stop the beeping.

No i have not. Now i measured it. F7140 PIN 1 0.5 volts and increases slowly. Pin 2 the same. F7140 beebs from boths side and its not blown. Checked with diode mode the PPBUS line and it was 0.146.

For how long? This computer was connected to charger about 2 hours ago and it was not connected to battery or charger, and when i plug the battery it still shows 12 volts...

I have checked the board under the microscope and have not seen any waterdamaged areas. The only waterdamaged area was near the battery connector. I have the 3476 brd file but if anyone has the correct one 4942 i can tell you what capasitor was bad, but i still replaced it with the new one.

R7005 PIN 1 and the same in other side. dukefawks can you tell me what to do? It does not make sense that in C7132 is 12 Volts and in the R7005 Pin 1 is under 1.5 volts... What should i do now? What to check?

Can you tell how is it possible that board has in some other areas 12 volts? Like C7132 in PIN 1 and Q7130 in PIN 2 that goes to PPDCIN_G3H_CHGR and its only the Battery that is plugged in not the charger...

Well fuck. Well i need to order again a new one and come back here... Do you louis know anyone that sells good batteries in ebay? It would be great if you could help. Or anyone. Thanks!

So i checked those dukefawks and larossmann . R7005 = 1.295 Volts D7005 PIN 1 = 0.025 Volts D7005 PIN 3 = 1.225 Volts And i checked the resistors value and it was same as in Schematics. What should i look next? This is new battery and the results are the same as before, even after replacing SMC.

No Title Here is a photo. If anyone could take from this side. Thanks!

If you could also take a photo from other side also where the wires can be seen. There are two big black wires and four blacks. And one white and green.

If somebody has macbook pro 13 2015 battery laying somewhere could you take a photo of the connector without the black tape covering it. Need to see the pins of where the battery cells connect to the little board that does not have schematics. Thanks!

I have an iphone 6 that is on 10.0.2 but the touch id is anoter iphones. Can i just update it or is the error 53 still a problem?

Thanks louis! I will check it and post here what found out. It will take time becouse im right now going to a trip but i will post the infromatiom right away when i'm working. :)

Yes, there is PPBUS line when the battery is plugged in without the charger.