Recent content by shanenin

  1. shanenin

    missing pm_slp_s4_L 820-3476

    I did , but maybe read it wrong
  2. shanenin

    missing pm_slp_s4_L 820-3476

    just curious, if we have 32.7 khz, does the imply we have all of these signals? Asking to try and understand
  3. shanenin

    missing pm_slp_s4_L 820-3476

    3.4 and 3.2 for the first two. I am not sure what 4 signals you are referring to. I am guessing this is to do with u1900 (I did swap it prior). I am getting 32.7khz on pin 12 of u1900
  4. shanenin

    missing pm_slp_s4_L 820-3476

    when I trigger smc_onoff_L while checking voltage of pm_slp_s4_L it stays at 0v. What is this checking for?
  5. shanenin

    missing pm_slp_s4_L 820-3476

    when I trigger SMC_ONOFF_L PM_PWRBTN_L drops fromm 3.4 volts to .3volts May I ask what this is helping us figure out?
  6. shanenin

    missing pm_slp_s4_L 820-3476

    Thanks. I am assuming trigger must mean short to ground. Can I check for a drop pulse by just holding a voltage meter on PM_PWRBTN_L? can I ask another question? how come I have 1.9volts on pp3v3_s0? Is that even possible without PM_SLP_S4_L?
  7. shanenin

    missing pm_slp_s4_L 820-3476

    I am working through a missing pm_slp_s4_L on an 820-3476. The board appears clean. here are the following readings PPVRTC_G3H : 3.3v PM_SYSRST_L :1.9v LOW? PM_PCH_PWROK: MISSING PM_RSMRST_L: 3.3v PM_PWRBTN_L: 3.3v SMC_ADAPTER_EN: 3.3v PM_BATLOW_L: 3.3v One of the issues seems to be...
  8. shanenin

    820-3476 no ppbus

    I double checked everything and the numbers I gave you seem correct. I also switched r7186. From what I can tell it seems like u7100 is not pulling the voltage down on chgr_agate.
  9. shanenin

    820-3476 no ppbus

    changed q7180, u7100, and r7185(just because). Still high voltage on chgr_agate_div. edit added later// let me double check all of the information I gave you. I think I may have made some mistakes
  10. shanenin

    820-3476 no ppbus

    I think I follow you. Even if chgr_agate_div is not turning on, but with 12 volts at chgr_sgate you should get something coming out of the q7180.
  11. shanenin

    820-3476 no ppbus

    Thank you 2informaticos for spending this extra time explaining stuff. I am asking the following question to understand, not argue. Before replacing q7180 don't we first need to get the enable fixed? On a working board both chgr_agate_div and chgr_sgate_div are about 6.5 volts. On this unworking...
  12. shanenin

    820-3476 no ppbus

    I was double checking my resistance reading on ppbus_g3h and I got .610 kohm, which I think is equal to 610 ohms. I also get this same reading on a known good board. That seems to be a good reading, but I may be doing something incorrectly, which happens more than I would like to admit. no...
  13. shanenin

    820-3476 no ppbus

    As you requested: ppbus_g2h resistance to ground 610ohm .123 diode mode r7180 99k r7181 62k r7185 470k r7186 300k isl6259 pin2 15.1v pin3 4v pin9 .04v pin19 5.46v pin20 5.46v May I ask a question? Is chgr_agate with its high voltage stopping q7180 from turning on? From what I think I...
  14. shanenin

    820-4924 no Keyboard and Mouse in OS after login?

    did you ever rule out a bad cable?
  15. shanenin

    820-3476 no ppbus

    I personally find it more beneficial to help me understand concepts than fixing the actual board
Top