Search results

  1. george-a

    820-01949 LD at left side (dual CD3217 next to each other)

    I soldered U2800 first.. then CD3217 ...also someone bought all JHL8040R from Mouser :D :D
  2. george-a

    820-01949 LD at left side (dual CD3217 next to each other)

    ok I received today the U2800(_X) and replaced the CD3217 that was corroded and voila!
  3. george-a

    820-01700 LD -> 20v / 0.045a

    ok I managed to install big sur by connecting to a different WiFi and I had to issue Terminal commands to start the installation from USB as the recovery procedure hanged. All good now.
  4. george-a

    820-01700 LD -> 20v / 0.045a

    ok thanks! Il check it out although I think its trolling me as I tried again earlier and got error 2002f... is this different? apologies for the bombardment of questions.
  5. george-a

    820-01700 LD -> 20v / 0.045a

    I flashed it in DFU choosing restore and it came back to life but internet recovery gives error 2003 and the laptop apparently is locked for USB booting.. any suggestions?
  6. george-a

    820-01700 LD -> 20v / 0.045a

    Hi guys, 820-01700 was LD near left hinge (as seen normally) and it is missing pp3v3_s5 but line has a diode mode of 0.330 The issue seems identical to this thread: https://boards.rossmanngroup.com/threads/820-01700-20v-0-03-amps.61049/ Other voltages look good and board is very clean. Any...
  7. george-a

    820-01949 LD at left side (dual CD3217 next to each other)

    yes I tested the board with same results -> 5V/0.280A Ill replace U2800 and check again - waiting for parts.
  8. george-a

    820-01949 LD at left side (dual CD3217 next to each other)

    ok now that schematics are out the shorted signal (pad48) of U3100_X was I2C_UPC_X_INTM_L which routes to pad10 of U2800_X (intel tb retimer).. when I removed U2800 the short cleared but I see that this IC is on two data buses (as shown in pic) - could this lead to T2 damage? --there were no...
  9. george-a

    820-01949 LD at left side (dual CD3217 next to each other)

    OK I used the thermal camera to detect the partial short of 0.09A of pad 48. It was the Intel Retimer JHL8040R (every CD3217 has one JHL8040R companion), and when removed the short cleared. I soldered back the second CD3217 (good one) I removed at the beginning to take comparison measurements...
  10. george-a

    820-01949 LD at left side (dual CD3217 next to each other)

    I used 820-01700 as a reference exactly because it has CD3217s - I didn't know TBT_T_CIO_PWR_EN is firmware depended but I assumed its the same in all motherboards that use that chip. Question is if this signal is shorted on one CD3217 does that mean that the PCH or something else on that line...
  11. george-a

    820-00850 no image, no touchbar image

    there is no image I believe but I think you cant really verify this on these LCDs with a flash light right? BKLT voltage at 55V. And unfortunately no spare LCD as these are hard to get by even damaged ones.
  12. george-a

    820-01949 LD at left side (dual CD3217 next to each other)

    Hi guys, little water damage at CD3217 closest to the hall sensor on the side where there are 2x CD3217s together. Cleaned and removed the chip to find out that 3rd ball from the top left (ball 48?) is short to ground (had to remove the other CD3217 to double check although I could also see...
  13. george-a

    820-00850 no image, no touchbar image

    I managed to flash it using Catalina, macbook pro 13" 2014 and RECOVERY mode.. works only on external maybe internal gpu is toast.
  14. george-a

    iMac 820-00291 with sensor issues

    Wil try that. The iMac was opened for some upgrade by the customer and this happened upon re-assembling it.
  15. george-a

    iMac 820-00291 with sensor issues

    Hi guys, I do not do iMacs (not very often at least) but this one belongs to a really nice customer and want to give it a try. High fan speed and the photo is from the temp sensors... I checked for missing thermal sensors (like Q5670 etc) but they are all there.. could it be U5650? Thanks...
  16. george-a

    820-00850 no image, no touchbar image

    I think yes, I will try again today. In the meantime if you can think of something else please shoot!
  17. george-a

    820-00850 no image, no touchbar image

    Ok it starts and ends up with a padlock.
  18. george-a

    820-00850 no image, no touchbar image

    I will, silly question but can it be done with a pre-2016 macbook and USB-A to C?
  19. george-a

    820-00850 no image, no touchbar image

    Hi guys, nice to be here again, need to update myself to latest development and there is no other place for that. I have a 820-00850 that switches to 20V only when the battery is connected. It will then draw 0.8-0.9A (possibly fully charged batt) and will give PPVCC_S0_CPU 1V. The fans spin...
  20. george-a

    820-3536 came back from the dead but no Backlight (although PPVOUT_S0_LCDBKLT = 52V?)

    well after looking closely with the microscope the 1st pin seems loose... glad it didnt short. was not obvious with naked eye and also the connectors had no problem sliding in...
Top