Macbook Pro A1706---820-00239

[hani]

the Amp meter shows 20v- 0.06A
Resistance To Ground for the big coils:
L7030 = 292
L8410 = 1074
L7660 = 341
L7600 =409
L3500 = 150

PPDCIN_G3H_CHGR = 20 V
PPVBAT_G3H_REG = 13 V
PPBUS_G3H = 13 V
PP5V_S4 = 0 Volt
PP3V3_S5 = 3.3 Volt
P3V3G3h = 4.9 V !!!!
3V0_G3H = 3 V

 

[2informaticos]

4.9V for sure at R6915?
In such case, check R6910-13 ohm values.
You can play with this resistor divider, to adjust output voltage.

 

[hani]

now PP3V3_G3H = 3.3 volt
but Nothing change
the Amp meter reads 20v 0.06 A

 

[2informaticos]

Do you get 3V3_SUS?
Post PM_PWRBTN_L, PM_RSMRST_L, PM_BATLOW_L, PM_DSW_PWRGD.

 

[hani]

3.3 volt on all the points

 

[hani]

is it normal ? PP5V_S4 = 0 Volt

 

[2informaticos]

Is SMC_ONOFF_L steady high?
If not, disconnect TouchID and check again.
If yes, trigger SMC_ONOFF_L and check for drop pulse at PM_PWRBTN_L at same time.
Be sure PM_RSMRST_L remains high all the time.

 

[hani]

i dont understand what do u mean by trigger SMC_ONOFF_L and check for drop pulse at PM_PWRBTN_L at same time.
smc_onoff_l is high 3.3 volt
PM_RSMRST_L high all the time

 

[hani]

i dont understand what do u mean by trigger SMC_ONOFF_L and check for drop pulse at PM_PWRBTN_L at same time.
smc_onoff_l is high 3.3 volt
PM_RSMRST_L high all the time

 

[2informaticos]

"i dont understand what do u mean by trigger SMC_ONOFF_L"
You should, as we talk such many times about that on the forum.
Read more threads, you can find lot of information.

I mean to press power button.
However, to work with board alone on the desk, use a pad or test point for SMC_ONOFF_L to solder an wire and temporary touch ground with it.
R5225/6 pads are good enough...

 

[hani]

update
after trigger SMC_ONOFF_L and check for drop pulse at PM_PWRBTN_L at same time.(from 3.3volt to 0.3 volt)
PM_RSMRST_L remains high all the time. (3.3 volt)
nothing change on the usb meter ( 20.1 volt - 0.06 A)

 

[2informaticos]

Check if all PM_SLP_Sx_L signals pulse at same time.

 

[hani]

PM_SLP_S5_L = 3.3
PM_SLP_S4_L = 0
PM_SLP_S3_L = 0
PM_SLP_S0_L = 3.3
PM_SLP_SUS_L = 3.3

 

[2informaticos]

No pulse at all at PM_SLP_S4_L for sure?
In such case, there is PCH related problem.

 

[hani]

Sure no pulse at PM_SLP_S4_L
RTC_RESET_L = 3 v
PCH_SRTCRST_L = 2.9 V
PCH_INTRUDER_L = 1.5 V
PPDCPRTC_PCH = 1.1 V
PM_DSW_PWRGD = 3.3 v
PPV0PCH_REG_R = 0.9 V
PP1V_PCH_REG_R=1.5 V
voltage on big coil L7030 Cant detected changed from 25 to 31 TBA phase 2

 

[hani]

is it pch??

 

[2informaticos]

"PCH_INTRUDER_L = 1.5 V"
There is a problem.
You can force the signal, lowering its resistor; 100K, instead of 1M.

 

[hani]

now PCH_INTRUDER_L = 3 V
nothing change (20 v 0.06 A)

 

[2informaticos]

"Check if all PM_SLP_Sx_L signals pulse at same time."
Test again...

 

[hani]

no
the same reading