820-02016 - No Trackpad / Keyboard

[2informaticos]

JT400 gets all power rails?
Check LT400-3.

 

[HeyWatchOutDude]

LT400 = 11.97V - seems to be low.
LT401 = 3.3V
LT402 = 3.3V
LT403 = 5.2V

 

[2informaticos]

Did you check on the output pin of the coils?

11.97V may be correct, if battery is connected.
If not, bypass the coil.

 

[HeyWatchOutDude]

I have checked both sides, same results. (LT400-3)

11.97V without battery connected. (battery charging is working)

What do you mean with "bypass the coil"?

 

[2informaticos]

Post LT400 voltage on both pins.

 

[2informaticos]

PPBUS_AON can't be 11.97V, if battery is not connected.

Check UR200 signals, when close/open the lid.

 

[HeyWatchOutDude]

But it is. (With battery connected - fully charged - it is 13.1V)

UR200 signals are fine, IPD_LID_OPEN_1V8 = 0V when closed and = 1.8V when opened.

 

[2informaticos]

Without battery, PPBUS_AON must be 13V.

 

[HeyWatchOutDude]

Any idea what else can be the cause of the none working trackpad/keyboard?

 

[2informaticos]

UT310/60/65 are also involved.
Also check all series resistors placed on SPI_IPD lines.

 

[HeyWatchOutDude]

I have replaced all three ICs (UT310/60/65) ... just in case - the issue consists.

RT372-376 = fine
RT303-304 = fine
RT305-307 = should be 47k ohms (at least it's written in the schematics) ... I have measured 6.8k ohms. (similar measurements on a donor board - so I guess it's fine?)

Is it normal that "IPD_SPI_EN" is always 0V?

• IPD_SPI_EN_CON = 0.596

• IPD_SPI_EN = 0.316

 

[2informaticos]

No, it should be high.

 

[HeyWatchOutDude]

Ok U0600 (M1) is generating it, right?

But diode value is fine - Source: https://openboarddata.org/?a=showboardsolutions&bpath=laptops/apple/820-02016

 

[2informaticos]

Possibly M1 problems; considering it doesn't complete DFU, nor enabling TP/KB.

 

[HeyWatchOutDude]

So IPD_SPI_EN should always be high even when I just take measurements on the logic board (without anything connected - except USB-C ports)?

 

[2informaticos]

Not sure if previous communication through I2C bus is required; for trackpad recognition.
You can check on working board, if available.

On T2 and Mx models, TP/KP use only SPI mode.

 

[HeyWatchOutDude]

Sadly I don’t have a working one.

DFU restore should complete even with no keyboard/trackpad functionally right?

Edit: https://boards.rossmanngroup.com/threads/a2442-820-02098-no-keyboard-or-trackpad.64468/ here it was also 0V, so I think it’s normal.

Edit2: What does AC2 error 16383 mean?

 

[HeyWatchOutDude]

macOS finder restore logs:

BEGIN: RESTORED:[0x0647] cleanup_check_result
[21:16:52.2653] restore-step-ids = {0x1103067B:61;0x11030635:67;0x1103130C:72;0x11030647:75}
[21:16:52.2653] restore-step-names = {0x1103067Berform_restore_installing;0x11030635:update_device_firmware;0x1103130C:update_aht;0x11030647:cleanup_check_result}
[21:16:52.2653] restore-step-uptime = 64
[21:16:52.2653] restore-step-user-progress = 38
[21:16:52.2653] [00:04:39.0948-GMT]{4>6} CHECKPOINT END: RESTORED:[0x0647] cleanup_check_result
[21:16:52.2653] restore-step-ids = {0x1103067B:61;0x11030635:67;0x1103130C:72}
[21:16:52.2653] restore-step-names = {0x1103067Berform_restore_installing;0x11030635:update_device_firmware;0x1103130C:update_aht}
[21:16:52.2653] restore-step-uptime = 64
[21:16:52.2653] restore-step-user-progress = 38
[21:16:52.2653] [00:04:39.0948-GMT]{4>6} CHECKPOINT BEGIN: RESTORED:[0x0648] cleanup_send_final_status
[21:16:52.2653] restore-step-ids = {0x1103067B:61;0x11030635:67;0x1103130C:72;0x11030648:76}
[21:16:52.2653] restore-step-names = {0x1103067Berform_restore_installing;0x11030635:update_device_firmware;0x1103130C:update_aht}
[21:16:52.2653] restore-step-uptime = 64
[21:16:52.2653] restore-step-user-progress = 38
[21:16:52.2653] 30C:update_aht}
[21:16:52.2653] restore-step-uptime = 64
[21:16:52.2653] restore-step-user-progress = 38
[21:16:52.2653]
[21:16:52.2653] ==== end of device restore output ====
[21:16:52.2687] AMRAuthInstallDeletePersonalizedBundle
[21:16:52.2687] preserved personalized bundle: (null)
[21:16:52.2687] <Restore Device 0x1226b7650>: Restore failed (result = -1)
[21:16:52.2687] Can't send dump_console command since device is not in recovery mode
[21:16:52.2687] Finished RestoreOS Restore Phase: Failed
[21:16:52.2688] State Machine Dump, status:ERROR - [stateFU remaining-cycles:1] -> [state:Recovery remaining-cycles:0] -> [state:RestoreOS remaining-cycles:0 (current state)]
[21:16:52.2691] Changing state from 'Restoring' to 'Error'
[21:16:52.2691] State is now set to error: AMRestorePerformRestoreModeRestoreWithError failed with error: -1
[21:16:52.2696] Restore completed, status: 7
[21:16:52.2696] Elapsed time (in seconds): 104
[21:16:52.2696] Restore Checkpoint Fingerprint: 130C.FFFF
[21:16:52.2696] Failure Description:
[21:16:52.2696] Depth:0 Code:-1 Error:AMRestorePerformRestoreModeRestoreWithError failed with error: -1
[21:16:52.2696] Depth:1 Code:-1 Error:Failed to handle message type StatusMsg (Generic error)
[21:16:52.2696] Depth:2 Code:-1 Error:failed to update device firmware
[21:16:52.2696] Depth:3 Code:-1 Error:ramrod firmware update failed
[21:16:52.2696] Depth:4 Code:7 Error:update_aht_block_invoke: ipd update failed with code 0xE00002C0.
[21:16:52.2696] Error: ((iokit/common) no such device)
[21:16:52.2696]